NHH-33A-R2B
6-port sector antenna, 2x 698–896 and 4x 1695–2360 MHz, 33° HPBW, 2x RETs and 2x SBTs
Features and benefits
- Narrow beamwidth capacity antenna for higher level of densification and enhanced data throughput
- Internal SBT on low and high band allow remote RET control from the radio over the RF jumper cable
- Separate RS-485 RET input/output for low and high band
- One LB RET and one HB RET. Both high bands are controlled by one RET to ensure same tilt level for 4x Rx or 4x MIMO
Specifications
General specifications
| Antenna Type | Sector |
| Band | Multiband |
| Color | Light Gray (RAL 7035) |
| Grounding Type | RF connector body grounded to reflector and mounting bracket |
| Performance Note | Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN |
| Radome Material | Fiberglass, UV resistant |
| Radiator Material | Aluminum | Low loss circuit board |
| Reflector Material | Aluminum |
| RF Connector Interface | 4.3-10 Female |
| RF Connector Location | Bottom |
| RF Connector Quantity, high band | 4 |
| RF Connector Quantity, mid band | 0 |
| RF Connector Quantity, low band | 2 |
| RF Connector Quantity, total | 6 |
Remote electrical tilt (ret) information
| RET Interface | 8-pin DIN Female | 8-pin DIN Male |
| RET Interface, quantity | 2 female | 2 male |
| Input Voltage | 10–30 Vdc |
| Internal Bias Tee | Port 1 | Port 3 |
| Internal RET | High band (1) | Low band (1) |
| Power Consumption, idle state, maximum | 1 W |
| Power Consumption, normal conditions, maximum | 10 W |
| Protocol | 3GPP/AISG 2.0 (Single RET) |
Dimensions
| Width | 640 mm | 25.197 in |
| Depth | 235 mm | 9.252 in |
| Length | 1219 mm | 47.992 in |
| Net Weight, without mounting kit | 33 kg | 72.752 lb |
Array layout
| Click on image to enlarge. |
Port configuration
| Click on image to enlarge. |
Electrical specifications
| Impedance | 50 ohm |
| Operating Frequency Band | 698 – 896 MHz | 1695 – 2360 MHz |
| Polarization | ±45° |
| Total Input Power, maximum | 900 W @ 50 °C |
Electrical specifications
| Frequency Band, MHz | 698–806 | 806–896 | 1695–1880 | 1850–1990 | 1920–2200 | 2300–2360 |
| Gain, dBi | 15.7 | 16.3 | 18.0 | 18.2 | 18.6 | 19.4 |
| Beamwidth, Horizontal, degrees | 34 | 30 | 34 | 33 | 31 | 29 |
| Beamwidth, Vertical, degrees | 21.5 | 19 | 8.6 | 8 | 7.5 | 6.7 |
| Beam Tilt, degrees | 0–18 | 0–18 | 0–10 | 0–10 | 0–10 | 0–10 |
| USLS (First Lobe), dB | 20 | 17 | 15 | 15 | 15 | 15 |
| Front-to-Back Ratio at 180°, dB | 33 | 38 | 36 | 37 | 36 | 38 |
| CPR at Boresight, dB | 21 | 21 | 18 | 20 | 19 | 18 |
| Isolation, Cross Polarization, dB | 25 | 25 | 25 | 25 | 25 | 25 |
| Isolation, Inter-band, dB | 28 | 28 | 28 | 28 | 28 | 28 |
| VSWR | Return loss, dB | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 |
| PIM, 3rd Order, 2 x 20 W, dBc | -153 | -153 | -153 | -153 | -153 | -153 |
| Input Power per Port at 50°C, maximum, watts | 300 | 300 | 250 | 250 | 250 | 200 |
Mechanical specifications
| Effective Projective Area (EPA), frontal | 0.47 m² | 5.059 ft² |
| Effective Projective Area (EPA), lateral | 0.15 m² | 1.615 ft² |
| Mechanical Tilt Range | 0°–19° |
| Wind Loading @ Velocity, frontal | 503.0 N @ 150 km/h (113.1 lbf @ 150 km/h) |
| Wind Loading @ Velocity, lateral | 155.0 N @ 150 km/h (34.8 lbf @ 150 km/h) |
| Wind Loading @ Velocity, maximum | 685.0 N @ 150 km/h (154.0 lbf @ 150 km/h) |
| Wind Loading @ Velocity, rear | 728.0 N @ 150 km/h (163.7 lbf @ 150 km/h) |
| Wind Speed, maximum | 241 km/h (150 mph) |
Packaging and weights
| Width, packed | 797 mm | 31.378 in |
| Depth, packed | 402 mm | 15.827 in |
| Length, packed | 1370 mm | 53.937 in |
| Weight, gross | 50 kg | 110.231 lb |
Regulatory compliance/certifications
| Agency | Classification |
| ISO 9001:2015 | Designed, manufactured and/or distributed under this quality management system |
General specifications
| Antenna Type | Sector |
| Band | Multiband |
| Color | Light Gray (RAL 7035) |
| Grounding Type | RF connector body grounded to reflector and mounting bracket |
| Performance Note | Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN |
| Radome Material | Fiberglass, UV resistant |
| Radiator Material | Aluminum | Low loss circuit board |
| Reflector Material | Aluminum |
| RF Connector Interface | 4.3-10 Female |
| RF Connector Location | Bottom |
| RF Connector Quantity, high band | 4 |
| RF Connector Quantity, mid band | 0 |
| RF Connector Quantity, low band | 2 |
| RF Connector Quantity, total | 6 |
Remote electrical tilt (ret) information
| RET Interface | 8-pin DIN Female | 8-pin DIN Male |
| RET Interface, quantity | 2 female | 2 male |
| Input Voltage | 10–30 Vdc |
| Internal Bias Tee | Port 1 | Port 3 |
| Internal RET | High band (1) | Low band (1) |
| Power Consumption, idle state, maximum | 1 W |
| Power Consumption, normal conditions, maximum | 10 W |
| Protocol | 3GPP/AISG 2.0 (Single RET) |
Dimensions
| Width | 640 mm | 25.197 in |
| Depth | 235 mm | 9.252 in |
| Length | 1219 mm | 47.992 in |
| Net Weight, without mounting kit | 33 kg | 72.752 lb |
Electrical specifications
| Impedance | 50 ohm |
| Operating Frequency Band | 698 – 896 MHz | 1695 – 2360 MHz |
| Polarization | ±45° |
| Total Input Power, maximum | 900 W @ 50 °C |
Electrical specifications
| Frequency Band, MHz | 698–806 | 806–896 | 1695–1880 | 1850–1990 | 1920–2200 | 2300–2360 |
| Gain, dBi | 15.7 | 16.3 | 18.0 | 18.2 | 18.6 | 19.4 |
| Beamwidth, Horizontal, degrees | 34 | 30 | 34 | 33 | 31 | 29 |
| Beamwidth, Vertical, degrees | 21.5 | 19 | 8.6 | 8 | 7.5 | 6.7 |
| Beam Tilt, degrees | 0–18 | 0–18 | 0–10 | 0–10 | 0–10 | 0–10 |
| USLS (First Lobe), dB | 20 | 17 | 15 | 15 | 15 | 15 |
| Front-to-Back Ratio at 180°, dB | 33 | 38 | 36 | 37 | 36 | 38 |
| CPR at Boresight, dB | 21 | 21 | 18 | 20 | 19 | 18 |
| Isolation, Cross Polarization, dB | 25 | 25 | 25 | 25 | 25 | 25 |
| Isolation, Inter-band, dB | 28 | 28 | 28 | 28 | 28 | 28 |
| VSWR | Return loss, dB | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 |
| PIM, 3rd Order, 2 x 20 W, dBc | -153 | -153 | -153 | -153 | -153 | -153 |
| Input Power per Port at 50°C, maximum, watts | 300 | 300 | 250 | 250 | 250 | 200 |
Mechanical specifications
| Effective Projective Area (EPA), frontal | 0.47 m² | 5.059 ft² |
| Effective Projective Area (EPA), lateral | 0.15 m² | 1.615 ft² |
| Mechanical Tilt Range | 0°–19° |
| Wind Loading @ Velocity, frontal | 503.0 N @ 150 km/h (113.1 lbf @ 150 km/h) |
| Wind Loading @ Velocity, lateral | 155.0 N @ 150 km/h (34.8 lbf @ 150 km/h) |
| Wind Loading @ Velocity, maximum | 685.0 N @ 150 km/h (154.0 lbf @ 150 km/h) |
| Wind Loading @ Velocity, rear | 728.0 N @ 150 km/h (163.7 lbf @ 150 km/h) |
| Wind Speed, maximum | 241 km/h (150 mph) |
Packaging and weights
| Width, packed | 797 mm | 31.378 in |
| Depth, packed | 402 mm | 15.827 in |
| Length, packed | 1370 mm | 53.937 in |
| Weight, gross | 50 kg | 110.231 lb |
| Click on image to enlarge. |
| Click on image to enlarge. |
Regulatory compliance/certifications
| Agency | Classification |
| ISO 9001:2015 | Designed, manufactured and/or distributed under this quality management system |
Installation & videos
Installation instruction
Documentation & downloads
Assembly drawing
Product information
Product specification
Assembly drawing
Product compliance documentation
Product information
Product specification
Related products & accessories
Included products
Base station antennas
-
![]()
BSAMNT-3 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
Related products
Base station antennas
-
![]()
APS-XT Antenna Orientation and Location Sensing System
Included products
Base station antennas
-
![]()
BSAMNT-3 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
Related products
Base station antennas
-
![]()
APS-XT Antenna Orientation and Location Sensing System